Determination of Boiler Building Verticality in Power Plant Construction using Terrestrial Laser Scanner (TLS)

https://doi.org/10.22146/jgise.40846

Mohamad Bagas Setiawan(1*), Yulaikhah Yulaikhah(2), Ruli Andaru(3)

(1) Universitas Gadjah Mada
(2) Universitas Gadjah Mada
(3) Universitas Gadjah Mada
(*) Corresponding Author

Abstract


Nowadays, Indonesian government is focusing on build up infrastructures, especially power plant infrastructures to fulfil electrical energy needs. One of the power plants that will be built up is Waai power plant which located on Waai village, Maluku Province. Waai power plant had been postponed since 2014. In order to build this power plant, the advisability of the building needed to be checked from its verticality level. This level was determined by Terrestrial Laser Scanner (TLS). The TLS’s point clouds were registered using two methods, there are target to target and cloud to cloud methods. There are 65 beams on the power plant boiler building, but only 31 beams that used as the samples to assign the verticality of the boiler construction. The verticality level was set on the X-axis, Y-axis, and the resultant of the X and Y axis by using Pythagoras theorem after the bottom and top coordinates from each beam was determined. The Queensland Building and Construction Admission Standards and Tolerances Guide 2016 was used as tolerance of verticality level. The result of the verticality calculation presented on the X-axis consisted from -0ᵒ 1’ 26,678” to 0ᵒ 4’ 11,778” with the average was 0ᵒ 1’ 40,820” and major direction pointed the positive axis. On the Y-axis, the average was -0ᵒ 0’ 45,772” with -0ᵒ 3’ 33,345” as minimum and 0ᵒ 1’ 25,319” as the maximum and the major direction went to the negative axis. The verticality on the resultant of X and Y axis was from 0ᵒ 0’ 45,225” until 0ᵒ 4’ 15,674” with the average was 0ᵒ 2’ 27,057” and the direction was to the southeast. After the verticality number was compared with the tolerance, the verticality level was smaller than the standard on each beam. From the result, we can conclude that the boiler building on the Waai power plant can be categorized safe to reconstruct.

Full Text:

PDF


References

Biro Perencanaan dan Kerja Sama Mineral Kementerian Energi dan Sumber Daya (2015) Rencana Strategis Kementerian Energi dan Sumber Daya Mineral 2015-2019. Jakarta: Kementrian ESDM.

CD Surveys (2015) Site Engineering Services. Available at: http://www.cdsurveys.com/site-engineering-services.

Genchten, B. Van (2008) Theory and Practice on Terrestrial Laser Scanning, Learning Tools for Advanced Three-dimensional Surveying in Risk Awareness Project. doi: 978-84-8363-312-0.

Hidaka, N., Michikawa, T., Motamedi, A., Yabuki, N., dan Fukuda, T (2018) ‘Polygonization of point clouds of repetitive components in civil infrastructure based on geometric similarities’, Automation in Construction, 86(November 2017), pp. 99–117. doi: 10.1016/j.autcon.2017.10.014.

Kregar, K. Ambrožič, T., Kogoj, D., Vezočnik, R., dan Majertič, A. (2015) ‘Determining the inclination of tall chimneys using the TPS and TLS approach’, Measurement: Journal of the International Measurement Confederation, 75, pp. 354–363. doi: 10.1016/j.measurement.2015.08.006.

Queensland Building and Construction Commission (2016) Standards and Tolerances Guide. Available at: https://www.qbcc.qld.gov.au/sites/default/files/Standards_and_Tolerances_Guide_0.pdf.

Soudarissanane, S. (2016) The Geometry of Terrestrial Laser Scanning: Identification of Errors, Modeling and Mitigation of Scanning Geometry.

Victorian Building Commision (2015) Guide to Standards and Tolerance



DOI: https://doi.org/10.22146/jgise.40846

Article Metrics

Abstract views : 1785 | views : 3747

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.


Journal of Geospatial Information Science and Engineering (JGISE) ISSN: 2623-1182 (Online) Email: jgise.ft@ugm.ac.id The Contents of this website is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.