Melamine Acetate Preparation as a Urea-Formaldehyde Resin Additive for Particleboard Production

https://doi.org/10.22146/ajche.79192

Dicky Dermawan(1*), Lukman Al Ghani(2), Aditya Bayu Prawidya(3)

(1) Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Nasional Bandung, Indonesia
(2) Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Nasional Bandung, Indonesia
(3) Department of Chemical Engineering, Faculty of Industrial Technology, Institut Teknologi Nasional Bandung, Indonesia
(*) Corresponding Author

Abstract


Urea-formaldehyde (UF) resin binders for wood-based panel production often use melamine as an additive to improve both mechanical properties and environmental compliance. Direct fortification for efficient use of melamine remains a problem due to low solubility. Pizzi & coworkers suggested the use of more soluble melamine salts and demonstrated success in terms of product performance. However, their preparation method showed low productivity and inefficient use of material and energy. In their scheme, a batch reactor fed with 1 kg of water and 75 g of a stoichiometric amount of melamine and acetic acid produced only around 25 g of solid melamine acetate crystal. In contrast, the remaining 50 g remained dissolved in 991 g of water, which requires high of energy to evaporate. This paper reports an attempt to increase batch productivity and work towards the more efficient use of material and energy. The experiment showed that the successive addition of melamine and acetic acid to the batch up to the solubility limit of melamine at the same reaction condition increased melamine and acetic acid fed from 75 g to 165 g. This was followed by a significant increase in dry crystal yield from 25 g to 117 - 132 g. Feeding the mother liquor to the next batch decreased the water use to only 8% of the original requirement. This resulted in a highly efficient process, eliminating the need for energy-intensive melamine acetate recovery from the mother liquor. The addition of 2% - 4% wt. of the product to UF resin resulted in particleboard with significantly lower thickness swelling, an increase in MOR & IB strength, and lower formaldehyde emission.

Keywords


Melamine Acetate; Urea-Formaldehyde Resin; Particleboard

Full Text:

PDF


References

Li, J. & Zhang, Y., 2021. “Morphology and crystallinity of urea-formaldehyde resin adhesive with different molar ratios.” Polymers, 13, 673.

Lubis, M. A. R. & Park, B. D., 2020. “Influence of initial molar ratios on the performance of low molar ratio urea-formaldehyde resin adhesives.” Journal of the Korean Wood Science and Technology, 48(2), 136-153.

Mouratidis, P. I., Dessipri, E. & Pizzi, A., 2000. "New adhesive system for improved exterior-grade wood panels." International Symposium on Wood Adhesives, Salt Lake Tahoe, 197-200.

No, B. Y. & Kim, M. G., 2004. “Syntheses and properties of low-level melamine-modified urea-melamine-formaldehyde resins.” Journal of Applied Polymer Science, 93(6), 2559-2569.

Ali, R. A. M., Ashaari, Z., Uyup, M. K. A., Bakar, E. S., Lee, S. H. & Azmi, N.I.F., 2020. “Synthesis and evaluation of low viscosity melamine urea formaldehyde for bulking treatment of wood.,” J. Indian Acad. of Wood Science, 17, 176-182.

Jeong, B., Park, B.D., Causin, V., 2019. “Influence of Synthesis Method and Melamine Content of Urea-Melamine-Formaldehyde Resins to their Features in Cohesion, Interphase, and Adhesion Performance.” Journal of Industrial and Engineering Chemistry, 79, 87-96.

Wang, B., Zhang, Y., Tan, H., & Gu, J., 2019. “Melamine-urea-formaldehyde resins with low formaldehyde emission and resistance to boiling water.” Pigment and Resin Technology, 48(3), 229-236.

Popovic, M., Momcilovic, M.D., Grmusa, I.G., 2020. “New Standards and regulations on formaldehyde emission from wood-based composite panels.” Zatista Materijala, 61(2), 152-160.

Kantieva, E. V., Ponomarenko, L. V., & Starodubov, A. S., 2020. “Monitoring hardeners of low toxic urea-formaldehyde resin.,” APITECH II Journal of Physics: Conference Series 1679, 042088.

Liu, C., Luo, J., Li, X., Gao, Q., & Li, Z. 2018. “Effects of compounded curing agents on properties and performance of urea formaldehyde resin.” Journal of Environmental Polymer Degradation, 26(6), 158-165.

Liang, J., Li, Q., Wu, Z., Du, G., Li, T., Lei, H., & Li, L., 2020. “Competitive polycondensation of model compound melamine-urea-formaldehyde (MUF) resin system by 13C NMR.” Journal of Bioresources and Bioproducts, 4 (1), 60-66.

Mao, A., Hassan, E. B. & Kim, M. G., 2013. “The effects of adding melamine at different resin synthesis points of low mole ratio UMF resins.” BioResources, 8(4), 5733-5748.

Lee, S. M., Park, J.Y., Park S. B., Han, S. T., & Kang, E. C., 2012. “Comparative study of the storage stability between a melamine-urea-formaldehyde and a urea-formaldehyde resin,” Forest Prod. J., 62(2),146–149.

Zanetti, M. & Pizzi, A., 2003. “Low addition of melamine salts for improved melamine-urea-formaldehyde adhesive water resistance.” Journal of Applied Polymer Science, 88(2), 287-292.

Ding, Z., Ding, Z., Ma, T. & Hua Z., 2021. “Acidic buffering capacity and curing process of the melamine-urea-formaldehyde resin.” Int. J. of Adhesion and Adhesives, 104(1), 102756.

Crews, G.M., Ripperger, W., Kersebohm, D.B., Seeholzer, J., & Guthner, T., 2002. Melamine and Guanamines, Ullmann’s Encyclopedia of Industrial Chemistry, 6th ed., Electronic Release.

Prestifilippo, M., Pizzi, A., Norback, H., & Lavisci P., 1996. “Low addition of melamine salts for improved UF adhesives water resistance.” European Journal of Wood and Wood Products, 54(6), 393-398.

Weinstabl, A., Binder, W. H., Gruber, H. & Kantner, W., 2001. “Melamine salts as hardeners for urea-formaldehyde resins.” Journal of Applied Polymer Science, 81(7), 1654-1661.

Cremonini, C. & Pizzi, A., 1999. “Field weathering of plywood panels bonded with UF Adhesives and low proportions of melamine salts.” European Journal of Wood and Wood Products, 57(5), 318.

Suzuki, N., Fukushima, K., Ichikawa, K., Saitu, T., & Inagaki, H., 1997. “Organic acid salt of melamine and thermosetting or photocurable thermosetting coating composition using the same.” US Pat. No. 5 604 080.

Tan, R. G. R. & Cruz, D.E., 2005. “Synthesis of robust water reuse networks using fuzzy nonlinear programming: mass exchange-based processes.” ASEAN Journal of Chemical Engineering, 5(1), 22-29.

Dermawan, D., 1998. “Pengaruh variabel proses pada pembuatan melamin asetat.” Proc. Seminar Nasional Itenas 2018, G14-G19.

Liu, X., Hao, J. & Gaan, S., 2016. “Recent studies on the decomposition and strategies of smoke and toxicity suppression for polyurethane-based materials.” RSC Advances, 6, 74720-74756.



DOI: https://doi.org/10.22146/ajche.79192

Article Metrics

Abstract views : 1496 | views : 959

Refbacks

  • There are currently no refbacks.


ASEAN Journal of Chemical Engineering  (print ISSN 1655-4418; online ISSN 2655-5409) is published by Chemical Engineering Department, Faculty of Engineering, Universitas Gadjah Mada.