Optimization Study of the Solid Propellant (Rocket Fuel) Based on Extracted Bitumen of Indonesian Natural Buton Asphalt

https://doi.org/10.22146/ajche.49732

Bardi Murachman(1*), Sajono Sajono(2), Fauzan Afandi(3), Johan Khaeri(4)

(1) 
(2) 
(3) 
(4) 
(*) Corresponding Author

Abstract


The asphalt propellant for rockets has been investigated since 1960. This material has been developed with the variation of fuels, oxidizer, binders, metal elements and additives. As solid propellant, it has some advantages and disadvantages during the implementation. At present, Extracted Buton asphalt has been studied as an alternative propellant fuels. It is a natural asphalt, extracted from Buton island asphalt rock. When the extract of buton asphalt is mixed with oxidizer, binder, and metal powder, it can be functioned as propellant which is able to release high intensity of energy, have strong thrust and power to fly the rocket. This optimization study of solid propellant was conducted by mixing the Buton asphalt as fuel, oxidizer, metal element and other additives to form a solid propellant. The oxidizer consisted of potassium nitrate (KNO3) and potassium perchlorate (KClO4). The variations of KClO4/KNO3, propellant density and the ratio of the nozzle diameter were also conducted in order to find the best propellant composition and the optimum operating conditions to produce enough power while maintain the integrity of the rocket. The main parameters such as the propellant’s thrust (F) and the specific impulse (Isp) were examined. The results showed that higher composition of KClO4/KNO3 gave the higher value of the thrust and the specific impulse. KClO4/KNO3 levels above the 1:1 ratio produced an explosive properties at the time of ignition. The tendency of propellant to explode during ignition process was also observed. The optimum condition was obtained at the KClO4/KNO3 ratio of 1:1 , the propellant density was 1.900 gram/cm3 and Ae/A* was 3.33. These conditions generated impulse value that last for 277.07 seconds, average thrust of 14.082 N, and average rate of combustion of 0,24 cm/second. Therefore, it can be concluded that propellant with fuel from extracted of Buton asphalt can be used as an alternative propellant for rocket.

Full Text:

PDF


References

1. Bakhman, N.N., Belyaev, A.F., Kondrashkov, and Yu, A., 1974, ”Effect of Metal Additives on Combustion Rate in Prototype Carburetion”, Army Foreign Science and Technology Center,
Charlottesville VA.
2. Douglas, H.W., Collins, J.H., Scortia, T.N., Cutforth, G.H., and Keller, R.B., 1971, “Solid Propellant Processing Factors in Motor Roket”, Lewis Research Center CZeveZund, Ohio, NASA, Washington.
3. Douglas, H.W., Collins, J.H., Scortia, T.N., Cutforth, G.H., and Keller, R.B., 1972, “Solid Propellant Grain Design and Internal Balistics”, Lewis Research Center CZeveZund, Ohio,NASA, Washington.
4. Douglas, H.W., Collins, J.H., Scortia, T.N., Cutforth, G.H., and Keller, R.B., 1973, “Solid Propellant Grain Structural Integrity Analysis”, Lewis Research Center CZeveZund,Ohio, NASA, Washington.
5. James, R.J., Robert, A.S., and John, C.F., 1966, ”Performance Of Rocket Nozzle Materials With Several Solid Propellants”, Lewis Reseurch Center CZeveZund, Ohio, NASA, Washington.

6. Ja’afar, M.N.M., Ali, W.H.W., Dahlan, M.D.N., and Rizalman, M., 2009, “Propelan Pepejal Kalium Nitral Difabrikasi Kaidah Acuan Mampat”, Journal Teknologim Universitas Teknologi Malaysia (In: Malayan)
7. Johnston, J.R., Signorezzi, R.A, and Freche, J.R., 1966, ”Performance Of Rocket Nozzle Materials With Several Solid Propellants”, Lewis Reseurch Center, Czevezund, Ohio, NASA,
Washington, p. 6.
8. Murachman, B., Purwono, S., dan Wintoko, J., 2009, “Laporan Rusnas UGM 2009: Propelan Padat Sebagai Bahan Pendorong Roket Menggunakan Bitumen Aspal Buton”, Laboratorium Minyak Bumi dan Batubara, UGM, Yogyakarta.
9. Mugia. E, 1996, “Simulasi Uji Statik Motor Roket Propelan Padat”, Program Magister Instrumentasi dan Kontrol, Program Pasca Sarjana, Institut Teknologi Bandung, Bandung.
10. Nuryanto, A., 2008,”Aspal Buton dan Propelan Padat”, LAPAN, Jakarta.
11. Sarmidi, 1996, ”Teknologi Roket untuk Perang dan Damai”, Sinar Harapan, No. ISBN STTM7, Jakarta (In: Indonesia).

12. Sarner, S.F., 1966, “Propellant Chemistry”, Reinhold Publishing Corporation, New York.
13. Sutton, G.P. dan Ross, D.M., 1976, “Rocket Propulsion Elements An Introduction to the Engineering of Rocket”, John Wiley & Sons, 4 edition, New York.
14. Sutrisno, 1997, “Pengaruh Elemen Aditif Terhadap Sifat-Sifat Propelan Padat Polibutadien-HTPB”, Tesis S2 Jurusan Ilmu Material, Program Pasca Sarjana Universitas Indonesia, Jakarta.
15. Syarkawi, A., 2002, “Kinerja Propelan Padat Komposit Polibutadien dalam Kaitannya dengan Komposisi Bahan- Bahannya”, LAPAN, Jakarta.

16. Thiokol Propulsion (An Alcoa Business), 2000, Rocket Basics A Guide To Solid Propellant Rocketry, Brigham City, Utah.
17. Vesna, R. and Petric, M., 2005, “The Effect of Curing Agen on Solid Composite Rocket Propellant Characteristic”, Scientific-Technical Review, Vol.LV, No.1, Beograd.
18. www.nakka-rocketry.net, Richard Nakka's Experimental Rocketry Web Site, accessed at 15 April 2010, 21.00 WIB



DOI: https://doi.org/10.22146/ajche.49732

Article Metrics

Abstract views : 3626 | views : 6065

Refbacks

  • There are currently no refbacks.


ASEAN Journal of Chemical Engineering  (print ISSN 1655-4418; online ISSN 2655-5409) is published by Chemical Engineering Department, Faculty of Engineering, Universitas Gadjah Mada.