Preparation and Activity of Precipitated Ni-MgO/Al2O3 Catalysts for the Partial Oxidation of Methane

  • Luis F Razon Chemical Engineering Department, De La Salle University
  • Carlito M Salazar Chemical Engineering Department, De La Salle University
  • Hiroo Niiyama Department of International Development Engineering, Tokyo Institute of Technology, JAPAN
  • Long The Nam Doan Faculty of Chemical Engineering, Ho Chi Minh City University of Technology
Keywords: catalysis, methane, NiO-MgO/Al2O3, partial oxidation, precipitation, syngas

Abstract

The effect of catalyst preparation methods, NiO/MgO molar ratio and reaction temperature on the performance of Ni-MgO catalysts supported on Al2O3 in the partial oxidation of methane to syngas were investigated in a fixed-bed flow reactor. Three catalyst preparation methods (all slight variants of the precipitation method) produced comparable results in CH4 conversion, CO and H2 selectivities. Energy Dispersive X-Ray (EDX) analysis and the color of the catalysts after reaction showed that catalysts produced by simultaneous dissolution of the nickel and magnesium salts may have better carbon deposition resistance. NiO/MgO molar ratio significantly affected the performance of the catalyst. When the NiO/MgO ratio decreased, activity decreased. At a NiO/MgO molar ratio of 1/2 and a reduction temperature of 850°C, CH4 conversion and CO selectivity increased when reaction temperature increased while H2 selectivity remained almost the same. The catalyst gave excellent activity and remained stable after 5h time-on-stream.

References

1. Albertazzi, S., Arpentinier, P., Basile, F., Del Gallo, P., Fornasari, G., Gary, D., and Vaccari, A. (2003). “Deactivation of a Pt/γ- Al2O3 catalyst in the partial oxidation of methane to synthesis gas,” Appl. Catal. A, 247, 1-7.
2. Choudhary, V.R., Uphade, B.S., and Mamman, A.S. (1997). “Oxidative conversion of methane to syngas over nickel supported on commercial low surface area porous catalyst carriers precoated with alkaline and rare earth oxides”, J. Catal., 172, 281-293.
3. Choudhary, V.R., and Mamman, A.S. (1997). “Energy-efficient conversion of methane to syngas over NiO-MgO solid solution,” Applied Energy, 66, 161-175.
4. Hagen, J. (1999). Industrial catalysis: A Practical Approach. Weinheim, Wiley-VCH. Hu, Y.H., and Ruckenstein, E. (2002). “Binary MgO-based solid solution catalysts,” Catal. Rev., 44, 423-453 .
5. Hu, Y.H., and Ruckenstein, E. (2004). “Catalytic conversion of methane to synthesis gas by partial oxidation and CO2 reforming,” Adv. Catal., 48, 297-345.
6. Hui, D., Guoxing, X., Zongping, S., Shenglin, L., and Weishen, Y. (2000). “Partial oxidation of methane to syngas in a mixed-conducting oxygen permeable membrane reactor,” Chinese Science Bulletin, 45, 3, 224-226.
7. Pantu, P., and Gavalas, G.R. (2002). “Methane partial oxidation on Pt/CeO2 and Pt/Al2 O3 catalysts,” Appl. Catal. A, 223, 253-260.
8. Ruckenstein, E., and Hu, Y.H. (1999). “Methane partial oxidation over NiO/MgO solid solution catalysts,” Appl. Catal. A, 183, 85- 92.
9. Utaka, T., Al-Drees, S.A., Ueda, J., Iwasa, Y., Takeguchi, T., Kikuchi, R., and Eguchi, K. (2003). “Partial oxidation of methane over Ni catalysts based on hexaaliminate- or perovskite-type oxides,” Appl. Catal. A, 247, 125–131.
Published
2007-12-31
How to Cite
Razon, L. F., Salazar, C. M., Niiyama, H., & Doan, L. T. N. (2007). Preparation and Activity of Precipitated Ni-MgO/Al2O3 Catalysts for the Partial Oxidation of Methane. ASEAN Journal of Chemical Engineering, 7(2), 108-109. Retrieved from https://dev.journal.ugm.ac.id/v3/AJChE/article/view/7683
Section
Articles