Vulcanization Kinetics of Natural Rubber Based On Free Sulfur Determination

https://doi.org/10.22146/ijc.21321

Abu Hasan(1*), Rochmadi Rochmadi(2), Hary Sulistyo(3), Suharto Honggokusumo(4)

(1) Department of Chemical Engineering, State Polytechnic of Sriwijaya, Jl. Srijaya Negara Bukit Besar, Palembang 30139
(2) Department of Chemical Engineering, Faculty of Engineering, Universitas Gadjah Mada, Jl. Grafika no. 2 Yogyakarta 55281
(3) Department of Chemical Engineering, Faculty of Engineering, Universitas Gadjah Mada, Jl. Grafika no. 2 Yogyakarta 55281
(4) Gapkindo (The Indonesian Rubber Association), Jl. Cideng Barat no 62A Jakarta 10150
(*) Corresponding Author

Abstract


The determination of free sulfur in the rubber vulcanizates provided significant representation of vulcanization reaction. In this research, the effects of vulcanization temperature, the mixing method of carbon black into rubber, the ingredients mixing sequence and the type of carbon black were studied on masticated and milled natural rubber in which the reaction was observed by un-reacted sulfur determination. The results showed that higher vulcanization temperature provided faster vulcanization reaction and greater reaction rate constant. Similarly, the mixing sequence of ingredient and carbon black into rubber influenced the rate of vulcanization reaction. The subsequent ingredients mixing sequence, in this case, resulted in higher vulcanization rate compared to that of the simultaneous one. However, the mixing method of carbon black into rubber brought small effect on the rate of vulcanization reaction. The type of carbon black applied was observed to influence the reaction rate of vulcanization. Smaller particle sizes of carbon black gave larger reaction rate constant. In this case, the type of carbon black N 330 gave faster vulcanization rate than that of N 660.

Keywords


natural rubber; kinetics; sulfur; vulcanization

Full Text:

Full Text Pdf


References

[1] Krejsa, M.R., and Koenig, J.L., 1993, Rubber Chem. Technol., 66. 3, 376–410.

[2] Morton, M., 1987, Rubber Technology, 3rd ed., Van Nostrand Reinhold, New York.

[3] Bideau, P.L., Ploteau, J-P., Dutournié, P., and Glouannec, P., 2000, Int. J. Therm. Sci., 48, 3, 573–582.

[4] Jaunich, M., Stark, W., and Hoster, H., 2009, Polym. Test., 28, 1, 84–88.

[5] Salgueiro, W., Samoza, A., Torriani, I.L., and Marzocca, A.J., 2007, J. Polym. Sci., Part B: Polym. Phys., 45, 21, 2966–2971.

[6] Pazur, R.J., Walker, F.J., and Plymout, M.I., 2011, Kautsch. Gummi Kunstst., 64, 1-2, 16, 18–23.

[7] Chough, S-H., and Chang, D-H., 1996, J. Appl. Polym. Sci., 61, 3, 449–454.

[8] López-Manchado, M.A., Arroyo, M., Herrero, J., and Biagiotti, J., 2003, J. Appl. Polym. Sci., 89, 1, 1–15.

[9] Ding, R., and Leonov. A.I., 1996, J. Appl. Polym. Sci., 61, 3, 455–463.

[10] Cotten, G.R., 1972, Rubber Chem. Technol., 45, 1, 129–144.

[11] Gerspacker, M., Niliel, L., Yang, H.Y., O’Farrel, C.P., and Schwartz, G.A., 2001, Flocculation in Carbon Black Filled Rubber Compounds, Meeting of the Rubber Division, American Chemical Society, Cleveland, Ohio, USA, October 16-19.

[12] Mahaling, R.N., Kumat, S., Rath, T., and Das, C.K., 2007, J. Elastomers Plast., 39, 253–268.

[13] Choi, S-S., 2004, J. Appl. Polym. Sci., 93, 3, 1001–1006.

[14] Choi, S-S., Hwang, K-J., and Kim, B-T., 2005, J. Appl. Polym. Sci., 98, 5, 2282–2289.

[15] Wang, P-Y., Qian, H-H., Yu, H-P., and Chen, J., 2003, J. Appl. Polym. Sci., 88, 3, 680–684.

[16] Wang, M.J., 2006, Effect of Polymer-Filler Interaction on Abrassion Resistance of Filled Vulcanizates, International Rubber Conference (IRC), Lyon-France, May 16-18.

[17] Wang, M-J., 1998, Rubber Chem. Technol., 71, 3, 520–589.

[18] Wang, M-J., 1998, The Role of Filler Networking in Dynamic Properties of Filled Rubber, Meeting of the Rubber Division, American Chemical Society. USA.

[19] Dannenberg, F.M., 1986, Rubber Chem. Technol., 59, 3, 512–524.

[20] Indian Rubber Institute, 2000, Rubber Engineering, McGraw-Hill, New York.

[21] Isayev, A.I., and Sujan, B., 2006, J. Elastomers Plast., 38, 291–318.

[22] Ximei, Sun, 2007, The Devulcanization of Unfilled and Carbon Black Filled Isoprene Rubber Vulcanizates by High Power Ultrasound, PhD Thesis, The Graduate Faculty of University of Akron, Ohio.

[23] Tricas, N., Escales, E. V., and Barros, S., 2002, Afinidad, 59, 337–342.



DOI: https://doi.org/10.22146/ijc.21321

Article Metrics

Abstract views : 2683 | views : 3940


Copyright (c) 2013 Indonesian Journal of Chemistry

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

 


Indonesian Journal of Chemistry (ISSN 1411-9420 /e-ISSN 2460-1578) - Chemistry Department, Universitas Gadjah Mada, Indonesia.

Web
Analytics View The Statistics of Indones. J. Chem.